FAAC J355 HA M50 bollard
Description
FAAC J355 HA M50 bollard is certified for the use in perimeter security; it has been purposely designed for the protection of sensitive areas, such as airports embassies, consulates, banks, harbors, etc.
FAAC J355 HA M50 bollard has been tested according to PAS 68:2013 Impact test specifications for vehicle security barrier systems and IWA 14-1:2013 – Vehicle security barriers – Part 1: Performance requirement, vehicle impact test method and performance rating.
FAAC J355 HA M50 bollard is able to stop a 7.500kg truck at a speed of 80Km/h (=50M/h).
FAAC J355 HA M50 main features are:
1. Tested according to PAS 68:2013 and IWA 14-1:2013
2. Integrated Hydraulic Unit concept
3. Kept lock in up position also in the event of power failure
4. Extreme care in the material selection
5. Rapid and silent movements
Specification
Hydraulic Automatic retractable HIGH SECURITY BOLLARD FAAC J355 HA M50, crash tested in accordance to PAS 68:2013 Impact test specifications for vehicle security barrier systems and IWA 14-1:2013 – Vehicle security barriers – Part 1: Performance requirement, vehicle impact test method and performance rating.
APPLICATIONS:
Sensitive areas, like: military sites, airports, embassies, consulates, banks, marine zones, prisons, industrial sites or wherever is required an high security level in terms of perimeter protection.
PRODUCT FEATURES:
FAAC J355 HA M50 bollard is made by a S355JR EN 10210 steel cylinder height 1.200mm off ground, diameter 355mm, thickness 30mm, with built-in reinforcement disks and surface anti-corrosive treatment in cataphoresis and polyester powder painted, or with additional jacket AISI 316L satin stainless steel.
The support structure is in reinforced steel. The bollard and the support structure are placed into a pit that sits in the foundation. All internal fixing frames are made of stainless steel, to prevent corrosion.
The cylinder head and ground crown are realized in AISI304 stainless steel
FAAC J355 HA M50 Bollard is designed to stop a 18.000 Kg 2-axle truck (nominal test vehicle mass 7.500kg), running at 80Km/hour and having capability to absorb at least an energy of 1.852.000 Joules as defined in accordance to PAS 68:2013 and IWA 14-1:2013.
Global bollard protection rate of the hydraulic unit is IP67.
Bollard speed on normal duty:
Rising time ~6 sec. / Lowering time ~3 sec.
The above operation time must be kept constant on defined duty cycle.
Cylinder above ground is visible on all environment conditions, having a 55mm reflecting strip all around the cylinder and LED lights that flash when bollard moves and stay permanently ON when upraised.
Hydraulic drive unit is integrated into the bollard structure, supplied at 230AC – 50/60Hz
In case of power failure, while the cylinder is upraised, it must remain in high position.
INSTALLATION COMPLEMENTS:
The bollard is installed in a dedicated pit complete with counter-frame and drainage set up.
CONTROL BOARD:
It’s supplied with 230VAC voltage – 50/60Hz.
The control board is external and must manage one bollard, equipped with a built-in dual loop detector and includes programmable logic and provides all commands for normal operation.
To link the bollard and the control board, a 16+1 conductors -min 1,5mm section- cable shall be employed.
OPERATING TEMPERATURE AND WEATHER CONDITIONS:
Bollard shall be fully operational within following conditions:
Operating temperature -15 °C / +55 °C
Operating temperature with heater (accessory) -40 °C / +55 °C
OPTIONS:
The cylinder finishing can be:
– Cataphoretic and polyester powder painted Dark grey metallized
– Stainless steel satin finishing
ACCESSORIES:
A Pit heater can be added, to operate also at extreme low temperatures.
A manual release safety kit can be added to lower the cylinder in case of blackout.
| Name | Value |
|---|---|
| Asset Type | retractable |
| Code Performance | PAS 68:2013 and IWA 14-1:2013 |
| Colour | grey anthracite RAL7021 |
| Created By | FAAC |
| Created On | 2016 |
| Description | retractable automatic bollard for perimeter protection |
| Features | integrated Hydraulic unit security; |
| Finish | painted or satin stainless steel |
| Manufacturer | www.faacbollard.com |
| Material | S355JR EN10210 steel |
| Model Reference | 116351: 116381 |
| Name | J355 HA M50 painted steel; J355 HA M50 satin finishing ; J355 HA M50 |
| Shape | round (cylinder) |
FAAC J355 M50 HIGH SECURITY bollards certified for perimeter protection
FAAC J355HA-M50 AUTOMATIC bollard
The automatic high security bollard FAAC J355 HA M50 has been tested according to PAS 68:2013 and IWA 14-1:2013 Standards, Impact resistance class N3 7.500-80 in SINGLE CONFIGURATION, this means it is able to stop a 7,500 kg lorry travelling at 80Km/h. Specifically designed and tested to protect extremely sensitive areas and all those areas with special perimeter security requirements against terroristic attacks.